FYI, If you decide to attempt any modifications to your HTX, you are doing so at your own risk. HTX Owners Manual HTX/Albrecht AE Service. Update*** I’m still doing this repair for those who may need it. Here are the specifics. I charge a flat fee of $35 which includes the new mic cord, the. Cat. No. OWNER’S MANUAL HTX TWO-METER MOBILE TRANSCEIVER Please read before using this transceiver. INTRODUCTION Your .
|Published (Last):||2 April 2014|
|PDF File Size:||1.50 Mb|
|ePub File Size:||9.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Table of Contents Add to my manuals Add.
The following charts should help you get a better idea of the func- tion of each control. Turn off the HTX Setting the Scan Resume Delay When you set the scan resume condition to cr carrierthe HTX resumes scanning after the carrier drops. Connect the antenna to your HTX using ohm coaxial cable. Replace the fuse in the holder and ht-252 it closed. So I just used the Pink in place of Manuwl.
The HTX transmits the stored sequence. Follow these steps to change the look-back time. Thus, a repeater that has an output frequency of Turning Auto Duplex On and Off The HTX can automatically select the correct duplex offset for frequencies normally assigned to repeaters and selects no offset simplex for other frequencies.
To switch between the two levels, press F then DIM. Tuning to a Standard Memory Channel. Setting the Frequency Step. If the transceiver still does not operate properly, take it to your local RadioShack store for assistance.
You can also set your HTX to limit reception to only those transmissions that include the selected tone. Getting a license is easier than ever.
Radio Shack HTX-252 Owner’s Manual
Mount the base station antenna according to its instructions. Vehicle cables and mounting hardware are sup- plied. Mine were yellow, yours might not be. May or may not be the case but drill at your own risk. You might need to connect the red wire directly to the battery if you experience ignition noise.
To store the frequency in a standard memory, press F. This gives users of low-power transceivers the ability to communicate over a much greater range.
Index of /k/kb1uif/downloads/Service & User Manuals/Radio Shack/HTX-252
All settings are cleared from the memory channel. Overriding the Duplex Offset. Hold on to the yellow sleeves that go over the Shield.
Directly Entering a Frequency. Keep the transceiver hx-252. The service you provide, gives an otherwise junk radio new life. To page an individual, you transmit their entire DTMF page sequence. Symptom Possible Cause and Solution Problems with reception Low is about 10 watts, and high is about 45 watts.
This transceiver opens nanual door for you to the world from almost any- where! Using an outdated browser makes your computer unsafe. The transceiver stops on each active frequency for 5 seconds if squelch is on. For example, if you tune to Follow these steps to change the scan resume delay. Hts-252 HTX displays rC and the currently set receive tone.
When it detects a transmission, it checks all memories to nanual if that frequency is already stored. This is for those residing in the US only.
Memory Channels Your HTX has 41 memory channels 40 standard memory channels and one calling-frequency memory channel. To turn the transceiver off, rotate counterclockwise until it clicks. Please update your browser!
Flashes when there is a transmission on Memory Channel 1 and the alarm is turned on.
Index of /k/kb1uif/downloads/Service & User Manuals/Radio Shack/HTX
Select the desired frequency. Page 8 Start studying for the license exams. Sensitivity 12 dB sinad. Scanning for a Frequency. The HTX can even scan a selected range and automatically store active frequencies in unused memory locations. FUNC — appears after you press F. Common Problems and Solutions. To do so, you need these items: Simply bring your Radio Manaul sales slip as proof of purchase date to any Radio Shack store.