View and Download Mitsubishi Electric FR-E instruction manual online. FR- E Inverter pdf Inverter Mitsubishi Electric Freqrol-A Instruction Manual. Part No: FR-ESK-EC, Brand: Mitsubishi, Model: E Series – kW V Download the Mitsubishi E Manual and Installation Guide from the links. changes both to this manual and to the specifications and design of the hardware at any . struction Manual of the frequency inverter FR-E This Installation.
|Published (Last):||17 November 2012|
|PDF File Size:||9.73 Mb|
|ePub File Size:||18.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
If the operation mode cannot be changed, refer to page This mode is displayed only in PU operation. Set them according to the operation specifications, load, etc.
Chapter 4 Parameter number Chapter 5 Chapter When connecting the high power factor converter FR-HC to suppress power harmonics, wire as shown below. Don’t show me this message again. Wrong connection will damage the high power factor converter and inverter.
Instruction Manual Fr-e Mitsubishi FREQROL Inverters | eBay
Page Page – Meter frequency manuaal calibration Pr Check the corresponding areas. Select the type of the no-fuse breaker NFB in response to the power Power factor supply capacity. Page 86 Page dreqrol – Parameters recommended to be set by the Input Filter Time Constant pr. If a data error is detected and a retry must be made, execute retry operation with the user program. Manusl frequency range 0.
These settings differ in starting method. Ground Fault Detection At Start pr. Surge voltages attributale to the wiring constants may occur at the motor terminals, deteriorating the insulation of the motor. Cable conforming to EIA e. Page 2 Thank you for choosing the Mitsubishi Transistorized inverter. Load Pattern Selection pr. Make sure that the front cover has been installed securely.
Installation And Wiring 2. When there is a commercial power supply-inverter switch-over circuit as shown below, the inverter will be kanual by leakage current from the power supply due to arcs generated at the time of switch-over or chattering caused by a sequence error.
Motor need not be connected. Page Page – Monitoring reference Pr. Got it, continue to print.
For the earth connection avoid feqrol contact between aluminium and copper. When data is transmitted from the computer to the inverter, codes CR carriage return and LF line feed are automatically set at the end of a data group on some computers. Page 20 – Removal and reinstallation of the access Ground fault detection is made only immediately after the start signal is input to the inverter.
Instruction Manual Fr-e500 Mitsubishi FREQROL Inverters
Prepare required instruments and parts according to the operation mode. This function is effective for switching the timing of electromagnetic brake operation between forward rotation rise and reverse rotation fall during vertical lift operation etc.
Parameter Name Application Number Maximum frequency Used to ffreqrol the maximum and minimum output frequencies. Set necessary parameter values according to the load and operating specifications.
On receipt of a data error occurrence, the inverter returns “reply data 3” to the computer again.
Page 69 1 Example: Fr-e to – ec; fr-es to – ec pages. Page 93 Page 94 – Electronic overcurrent protection Pr. When parameter clear or all clear is performed, each parameter returns to the factory setting.
Set “1” in Pr. Page of Go.
Mitsubishi Electric FR-E500 Instruction Manual
Connect and operate the option unit carefully in accordance with the corresponding option unit manual. Remote Setting Function Selection pr. When the control panel is used, the same value as on the PU is only displayed: Set “” in Pr. Operation mode can be switched to PU operation mode.
Page – Cooling fan operation selection Pr. Page 91 – Multi-speed operation Pr. Reverse rotation For example 1 Inverter status b3: Corrective action Set the ambient temperature to within the specifications. E500 following table lists the cables and crimping terminals used with the inputs R L S LT L and outputs Freqdol, V, Frwqrol of the inverter and the torques for tightening the screws: Since their values depend on the static capacitance, carrier frequency, etc.
Pwm Carrier Frequency pr. When no alarm exists, E.