ASTM International ASTM D Tearing Strength of Fabric by . ASTM International. D Breaking Strength/Elongation Grab Method. ASTM D is a testing standard for determining the breaking strength and elongation of woven, non-woven, and felted fabrics and textiles. ASTM D is a popular testing standard for those needing to determine the breaking strength and elongation of fabrics and textiles.
|Published (Last):||20 March 2012|
|PDF File Size:||16.87 Mb|
|ePub File Size:||11.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is the responsibility of the user of this standard qstm establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.
This test method is particularly applicable to high-strength fabrics. Glossary of Materials Testing Terms. SI units is s5034 technically correct name for the system of metric units known as the International System of Units.
Inch-pound units is the technically correct name for the customary units used in the United States. Email addresses must contain the symbol.
ASTM D Breaking Strength and Elongation of Textile Fabrics Grab Test – Instron
The values stated in either acceptable metric units or in satm units shall be regarded separately as standard. Bluehill LE for Basic Testing. The values stated in either acceptable metric units or in other units shall be regarded astk as standard. Pneumatic side action grips with rubber coated jaw faces are well suited for clamping of the grab specimens.
Grab test specimens require much less time to prepare although they require more fabric per specimen. Subscribe to Our Newsletters.
This standard mainly applies to most woven textile fabrics, but can be applicable to fabrics produced by other techniques. It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements.
As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. Rapid data capture rate with Instron’s controller allows data peaks and valleys to be captured accurately at up to 2, points per second Instron pneumatic side action grips with rubber faces are well-suited to gripping nearly all types of fabric specimens for this test while maintaining high throughput It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements.
Special precautionary measures are provided for use when necessary for strong fabrics. SI units is the technically correct name for the system of metric units known as the International System of Units.
Inch-pound units is the technically correct name for the customary units used in the United States. WaveMatrix 2 for Dynamic Testing. Software for Series Systems. This is because when individual fibers within the fabric fail, the data rate must be fast enough to catch these peaks. Even then the data may differ significantly.
How can we help you?
Subscribe to Instron News! Historical Version s – view previous versions of standard. The challenges of testing to this standard are: Next Checking to see if you are a returning visitor…. Work Item s – proposed revisions of this standard.
ASTM D5034 Textile Strength and Elongation Grab Test
Rapid data capture rate Specimen gripping Instron’s Solution: Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. Competent statistical assistance is recommended for the investigation of bias.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in light of the known bias. Link to Active This link will always route to the current Active version of the standard. A grab test is a tensile test in which only the center part of the specimen not the full width is gripped in the jaw faces.
Active view current version of standard. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. Contact Us View Accessories Catalog.
There is no simple relationship between grab tests and strip tests since the amount of fabric assistance depends on the type of fabric and construction variables. Note 1—For the determination of the breaking force and elongation of textile fabrics using the raveled strip test procedure and the cut strip test procedure, refer to Test Method D Two sets of specimens are prepared, one in the warp machine direction and one in the filling cross direction.
Work Item s – proposed revisions of this standard. For this test, it is important to have an increased test data rate to ensure the capture a high number of data points. The method specifies a procedure to determine the maximum force and the elongation at maximum force of textile fabrics using a grab method.
Link to Active This link will always route to the current Active version of the standard. Provisions are made for wet testing. Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. The breaking force determined by the grab procedure is not a reflection of the strength of the yarns actually gripped between clamps and cannot be used for direct comparison with yarn strength determinations.