This OMRON 3G3EV-ABMA-CUE SYSDRIVE Inverter is used and in excellent condition. Configurations: A: Panel Mounting Installation Type B. Omron SYSDRIVE 3G3EV SERIES Pdf User Manuals. View online or download Omron SYSDRIVE 3G3EV SERIES User Manual. View and Download Omron SYSDRIVE 3G3EV user manual online. Compact Low-noise Inverter. SYSDRIVE 3G3EV Inverter pdf manual download.
|Published (Last):||19 July 2015|
|PDF File Size:||1.20 Mb|
|ePub File Size:||7.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
When warning status arises, no error code is output. Removing the Digital Operator S Insert a finger in the recessed section below the Digital Operator, then lift the under- neath of the Digital Operator.
Troubleshooting Chapter 5 Operation Troubleshooting If the Inverter or motor does not operate properly when the system is started, constant settings or wiring may be incorrect. Howev- er, all indicators are not lit when a ojron circuit error occurs. Proper use and handling of the product will ensure proper product performance, will length product life, and may prevent possible accidents.
Omron SYSDRIVE 3G3EV SERIES User Manual
Sysdrive 3g3mv series multi-function compact inverter pages. Set the word address in constant no. Check for abnormal heating.
Page 38 Chapter 4 Preparing for Operation H Monitor Display The 3G3EV allows the user to monitor the reference frequency, output fre- quency, output current, and the direction of rotation. If voltage is applied to the output terminals, the internal mechanism of the Inverter will be damaged. Resonance with the natural frequency of mechanical system Take special care when a machine that has been operated at a constant speed is to be operated in variable speed mode.
To prevent this, adjust the carrier frequency set in n37 as shown in the table below. Page 85 Chapter 7 Notes on Using Inverter for Motor Using Inverter for Existing Standard Motor When a standard motor is operated with this Inverter, a power loss is slightly higher than when operated with a commercial power supply.
Inverter monitors over-torque only when speed is matched. The constants for basic operations are allocated to dedicated indicators, so the user need not refer to the constant nos. Motor capacity should be also increased. We appreciate your interest in using our InstraView website! This may affect peripheral devices.
OMRON 3G3EV-ABMA-CUES1 – In Stock, We Buy Sell Repair, Price Quote
Chapter 4 Preparing for Operation Preparation Procedure 1. Therefore, constant numbers can be confirmed easily.
Chapter 4 Error code Description Error category n50 is used to specify whether over-torque is to be monitored and specify the action to be taken when over-torque is detected. D Never Short or Ground the Output Terminals Caution If the output terminals are touched with bare hands or the output wires come into contact with the Inverter casing, an electric shock or grounding will occur.
Mercury Drive Champaign, IL You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment.
Chapter 1 Getting Started If an inspection or some other task is to be performed, always wait at least one minute from the time all indicators on the front panel go off. Don’t have an account? Take the following actions to prevent noise: D Minimum Constant Setting Items Constant setting items have been minimized to enable even first-time users to set constants easily. Valid Email Required Item to Inspect: Chapter 4 Preparing for Operation Note MA is turned on when the difference between the reference frequency and the output frequency falls within 2 Hz.
In addition, cooling effects also decline in the low-speed range, resulting in an increase in the motor temperature. Monitor Display Chapter 4 Monitor Display The 3G3EV allows the user to monitor the reference frequency, output fre- quency, output current, and the direction of rotation.
The radiation fin overheated because Reduce the load. Check the motor for noise. We’ll send you an email letting you know exactly when your piece of equipment will be available for viewing Name: Page 56 Chapter 4 Error code Description Error category n50 is used to specify whether over-torque is to be monitored and specify the action to be taken when over-torque is detected. Chapter 4 Note 2.
Page 30 Chapter 3 Always separate the control signal line from the main circuit cables and other power cables. Please contact us to complete your request. Chapter 7 Gearmotor The speed range for continuous operation differs according to the lubrication method and motor manufacturer. When warning status arises, no error code is output. It continues operation even when over-torque is detected.
If the power supply for the main circuit is to be shut off because of the sequence, a mag- netic contactor can be used instead of a molded-case circuit breaker. Stock Quick Quote. Although care has been given in documenting the product, omorn contact your OMRON representative if you have any suggestions on improving this manual.